✨ Other Enhancements

• When IRIS Mode is set to Manual, laser brightness adjustment is available for IRIS Size levels 0–6 (Path: Settings → Display & Picture → Laser Luminance → Laser Luminance Level).
• When the projector is connected to ThunderBeat, the Audio system menu supports translations in 10 languages (Path: Settings → Sound → Audio System).
• Added AirPlay 2 support (for Aetherion Plus. Max and Pro already support).
• 3D Optimization: Improved 3D crosstalk performance and fixed the 3D Left & Right Switch functionality in 3D mode.
• Fixed other software bugs.
• Platform improvements. 

🟦 PART 1: ANDROID SOFTWARE UPGRADE GUIDE🟦

Note:

If the Network upgrade cannot detect a new version, this is because Google's system update strategy uses staged/percentage-based rollout, so the update may not be immediately available. Please wait patiently. 

If you prefer to update immediately, you have to use the other way to upgrade firmware thru USB upgrade method.

The recommended and easier way to finish the software updates is to use the Network Upgrade method. And with the Network Upgrade feature enabled, you will automatically receive a notification to update your projector.

The projector will automatically restart. Do not power it off during the entire upgrade process.

1. Connect to the network via Ethernet cable or Wi-Fi.

2. Press the Settings button on the projector remote control, then go to Settings → System → About → System Update → Upgrade from Network. Once a new version is detected, select Upgrade.

3. The projector will automatically download, verify, and install the update package following the demo steps below.

* Do not power off during update

4. Following the demo images below, select OK to restart.

5. Check the updated software version.

Press the Settings button on the projector remote control, then go to Settings → Help & Feedback → System Message → Software Version.

• If the version number is V0000.01.00U.Q1015, the software update was successful.

• If the version number is not V0000.01.00U.Q1015, it is recommended to upgrade the projector again.

⚠️The prefix of the version number varies depending on the region; only the last four digits need to be confirmed.

Note:

If your projector has no network connection, or you don't want to wait for the Google system update to be pushed, you can also update the software using a USB flash drive.

📝Important Notices (must read)

Read the instructions carefully or you could end up causing the projector to become unresponsive or require a repair.

• Do not turn off the projector or disconnect it from power while it is updating.
• Do not press any buttons except the ones mentioned in the instructions.
• Prepare a blank USB flash drive formatted in FAT32. Do not unplug the USB drive during the upgrade process.
• Check and disable features such as scheduled shutdown.
• Unplug external devices to prevent them from causing the device to shut down.

Step 1: Download the Update

Before you install the update, you'll need to download the update files from the Internet and save them to a FAT32 format only USB flash drive.

1. Download firmware:  Google Drive Link

2. Verify the downloaded file names and size.

• File Name: USBOTA_LASERS_20261015201500.zip
• File Size: 1,975,469,913 bytes

3. Connect the USB flash drive to your computer, go to the location where the downloaded files saved, and copy the USBOTA_LASERS_20261015201500.zip into the root directory of the USB flash drive.

4. Remove the USB flash drive from your computer and continue to the next steps.

Step 2: Install the Update

Note:

Once the update files are downloaded to your USB flash drive, install the files on your projector. The process can take up to 30 minutes and during the installation.

1. Make sure that no other USB devices are connected to your projector.

2. Connect the USB flash drive with upgraded files to the projector USB port, and it’s recommended to use the projector USB3.0 port.

3. Press the Settings button on the projector remote control, then select Settings → System → About → System Update → Upgrade from USB.

4. Select Upgrade, and the projector will automatically verify and install the update package.

5. Following the demo images below, select OK and remove the USB flash drive to restart the projector.

6. Check the updated Android software version

Press the Settings button on the projector remote control, then go to Settings → Help & Feedback → System Message → Software Version.

• If the version number is V0000.01.00U.Q1015, the software update was successful.

• If the version number is not V0000.01.00U.Q1015, it is recommended to upgrade the projector again.

⚠️The prefix of the version number varies depending on the region; only the last four digits need to be confirmed.

🟥 PART 2: DLP SOFTWARE UPGRADE🟥

📝Important Notices (must read)

Read all instructions carefully before proceeding. Incorrect installation may cause the projector to become unresponsive (hard-bricked) and require professional repair.

• Please first confirm projector’s Android software version is the latest version. Go to Settings → Help & Feedback → System Message → Software Version. If the version number is V0000.01.00U.Q1015, you are on the latest version.
• Do not turn off the projector or disconnect it from the power source during the update process.
• Do not unplug the USB drive during the upgrade process.
• Do not press any buttons except those explicitly mentioned in the instructions.
• Check and disable any automatic features such as scheduled shutdown or sleep timers.
• Unplug all external devices to prevent unintended shutdowns or interference.
• Turn off Wi-Fi and disconnect any network cables.
• After clicking the upgrade button, the screen will go black for a while and then return to normal. This is normal. The DLP firmware upgrade takes about 3 minutes, and the system will automatically restart after the upgrade is complete
• If the system does not automatically restart after 10 minutes, please manually restart the device.
• DLP firmware cannot be flashed across different projector models.

Step 1: Download the Update

Before you install the update, you need to download the DLP firmware from the Internet and save it to a USB flash drive formatted exclusively as FAT32.

Please ensure that the DLP firmware package you download is correct. An incorrect package may affect the normal operation of the projector.

1. Google Drive download links:

• Aetherion Max: Google Drive Link
• Aetherion Pro: Google Drive Link
• Aetherion Plus: No DLP firmware update is required.

2. Connect the USB flash drive to your computer, navigate to the folder where the downloaded files are saved, and only copy the 'dlp_upgrade.img' file for your corresponding model to the root directory of the USB flash drive.

3. Remove the USB flash drive from your computer and continue to the next steps.

Step 2: Install the Update

The process takes about 3 minutes, and the projector will automatically restart after the installation is complete.

1. Please disable the auto power-off related functions to prevent automatic shutdown during the upgrade process. The method is as follows:

Press the Settings button on the remote control to enter the Settings page, and follow the path: All settings → System → Power & Energy.

• Set the "When inactive" option of Shut-Off Timer to Never.
• Set Sleep Timer to off.
• Set Power Off Timer Type to off.

2. Make sure that no other USB devices are connected to your projector.

3. Connect the USB flash drive with the upgrade files to the projector's USB port, and it's recommended to use the projector's USB3.0 port.

4. Press the Settings button on the remote control to enter the Settings page, and follow the path: Settings → System →  About →  System update → DLP firmware update. Click the Update button to start the upgrade.

Please wait patiently for the upgrade to complete until the device automatically restarts. During the upgrade process, please do not press any buttons on the remote control to interrupt it, and do not disconnect the power or perform any shutdown actions, to avoid upgrade failure that could prevent the device from booting normally.

5. After the upgrade is complete, check the updated DLP software version.

Press the Settings button on the remote control to enter the Settings page, and follow the path：All settings → System → About → System update → DLP firmware update. Check the Current version.

• Aetherion Max: Firmware update succeeds when DLP version is 31. Re-upgrade if the version is not 31.
• Aetherion Pro: Firmware update succeeds when DLP version is 39. Re-upgrade if the version is not 39.

🧑‍💻Customer Support

• Website: https://awolvision.com/
• Email: support@awolvision.com

If you have any questions, please contact support@awolvision.com for further assistance.

https://awolvision.com/

support@awolvision.com